Skip to content
MeasureToBuy

Wall Area Calculator

Enter each wall's width and height, add a gable if the wall rises to a peak, and subtract doors and windows. You get the total and net wall area in square feet or square meters — the number paint, drywall and primer estimates start from.

Measurements

Advanced optionscoverage, sizes, custom values

A standard 3 × 7 ft door is 21 sq ft.

A typical 3 × 5 ft window is 15 sq ft.

Your estimate

Your net wall area is 81 square feet.

96 sq ft total, minus 15 sq ft of doors and windows.

Wall
96 sq ft
Total wall area
96 sq ft
Doors & windows
-15 sq ft
Net wall area
81 sq ft
In square meters
7.5 m²
Wall elevation
12 ft8 ft
Wall area = 12 ft × 8 ft. Doors (solid) and windows (dashed) are subtracted.

Next step

Turn the area into paint

Painting 81 sq ft of wall? The Paint Calculator adds coats and extra, then rounds to real cans.

Calculate paint

Also useful

Count drywall sheets

Hanging new board? Turn the room into sheets, mud, tape and screws.

Calculate drywall

How to measure

  1. Measure each wall's width along the floor, corner to corner.
  2. Measure height from floor to ceiling. For a gable wall, measure the rectangular part up to where the slope starts, then the gable from there to the peak.
  3. Count doors and windows. The default sizes are a 3 × 7 ft door (21 sq ft) and a 3 × 5 ft window (15 sq ft); change them under Advanced options.
  4. Measuring a whole room? Add four walls, or use length + width as one wall's width and double it.

How the wall area calculation works

Wall area   = width × height (each wall)
Gable area  = base width × gable height ÷ 2
Total area  = Σ walls + gables
Net area    = total − doors × door area − windows × window area

Each wall is a rectangle. A gable is the triangle on top of a wall under a pitched roof or vaulted ceiling: half its base times its height.

Doors and windows are subtracted from the total to give the area you'll actually cover. Small openings like outlets and vents aren't worth subtracting.

Worked example

A 12 × 10 ft room with 8 ft walls, a 24 ft wide gable 6 ft high above one end, one door and two windows.

  1. Walls: (2 × 12 × 8) + (2 × 10 × 8) = 352 sq ft
  2. Gable: 24 × 6 ÷ 2 = 72 sq ft
  3. Total: 352 + 72 = 424 sq ft
  4. Openings: 21 + (2 × 15) = 51 sq ft

Net wall area: 373 sq ft (about 34.7 m²).

Reading your result

Use the net wall area for paint and wallpaper primer. For drywall, pros often skip deducting small windows — the cut-outs are waste anyway.

The 'Total wall area' line is the gross figure some contractors quote by; check which one an estimate uses.

Assumptions

  • Walls are flat rectangles; gables are symmetrical triangles.
  • Doors are 21 sq ft and windows 15 sq ft unless you change them.
  • Openings larger than the wall are capped so the net area never goes below zero.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

Frequently asked questions

How do I calculate the square footage of a wall?

Multiply the width by the height. A 12 ft wall that's 8 ft high is 96 sq ft. Subtract about 21 sq ft for each door and 15 sq ft for each window.

How do I find the area of a gable wall?

Split it into a rectangle and a triangle. The rectangle is width × height to where the slope starts; the triangle is base × peak height ÷ 2. Add them together.

What's the wall area of a 12 × 12 room?

With 8 ft ceilings, 4 × 12 × 8 = 384 sq ft before doors and windows. One door and one window bring it to 348 sq ft.

Should I subtract doors and windows?

For paint and wallpaper, yes. For drywall, it depends: large openings save a sheet, but small windows usually come out of a sheet you'd buy anyway.

More area & volume calculators

All area & volume