Project planner
Install a fence
Lay out a fence run and get posts, panels or pickets and rails, gates and post-hole concrete — the same numbers as the Fence Calculator, split into steps with a printable list.
- 01 Fence layout
- 02 Posts & sections
- 03 Infill
- 04 Post concrete
- 05 Cost
- 06 Summary
Step 1: Fence layout
Total length, how many separate runs, height and gates.
Include the gate openings.
Count each straight stretch between corners or ends. Each run adds an end post.
Above ground.
Opening between gate posts.
Step 2: Posts & sections
Post spacing sets the section width; panels usually fix it at 8 ft (2.4 m).
- Fence length
- 100 ft
- Gate openings1 × 4 ft
- 4 ft
- Sections8 ft post spacing
- 13 sections
- Posts8 ft long (6 ft + 24 in in the ground)
- 15 posts
Step 3: Infill
Prebuilt panels, or pickets on rails.
A 1×4 picket is 3½ in wide; a 1×6 is 5½ in.
0 for a privacy fence, 1–2 in for spaced pickets.
- Pickets3.5 in wide, 0 in gap
- 330 pickets
- Rails3 per section × 12 sections, 8 ft long
- 36 rails
- Gates
- 1 gate
Step 4: Post concrete
Holes about three times the post width, a third of the height deep.
0 = automatic: ⅓ of the fence height, at least 24 in (600 mm). Go below the frost line where the ground freezes.
- Hole diameter3 × post width
- 10.5 in
- Hole depth⅓ of the height, minimum applied
- 24 in
- Concrete per holehole minus the post
- 1.03 cu ft
- Concrete for all posts
- 15.5 cu ft
- 50 lb fast-setting bags0.38 cu ft per bag
- 42 bags
Step 5: Cost
Prices from your supplier.
per postper picketper railper bagper gate- Posts
- $270.00
- Pickets
- $990.00
- Rails
- $324.00
- Concrete
- $336.00
- Gates
- $150.00
- Estimated material cost
- $2,070
MeasureToBuy · project summary
Fence project estimate
You need 15 posts and 330 pickets.
Measurements
- Total fence length: 100 ft
- Straight runs: 1
- Fence height: 6 ft
- Post spacing: 8 ft
- Fence style: Pickets and rails
- Picket width: 3.5 in
- Gap between pickets: 0 in
- Rails per section: 3
- Gates: 1
- Gate width: 4 ft
- Post size: 4×4
- Post hole depth: 0 in
- Concrete bag: 50 lb fast-setting
Key figures
- Fence length
- 100 ft
- Gate openings1 × 4 ft
- 4 ft
- Sections8 ft post spacing
- 13 sections
- Posts8 ft long (6 ft + 24 in in the ground)
- 15 posts
Shopping list
- Posts8 ft long (6 ft + 24 in in the ground)
- 15 posts
- Pickets3.5 in wide, 0 in gap
- 330 pickets
- Rails3 per section × 12 sections, 8 ft long
- 36 rails
- Gates
- 1 gate
- 50 lb fast-setting bags0.38 cu ft per bag
- 42 bags
- Estimated material cost
- $2,070
Material cost
- Posts
- $270.00
- Pickets
- $990.00
- Rails
- $324.00
- Concrete
- $336.00
- Gates
- $150.00
- Estimated material cost
- $2,070
Posts = 13 sections + 1 for the run end + 1 so each gate has its own hinge and latch post. Set gate posts deeper or use 6×6 posts — a swinging gate pulls harder on its post than any fence section. Hardware, nails or screws, gravel under the posts and post caps are not included. Buy 5% extra pickets for splits and knots. Height limits, setbacks, property lines and permits vary by town and HOA. Call 811 (or your local utility locator) before digging.
Calculators provide planning estimates. Actual material requirements vary with product specifications, installation method, site conditions, local codes and project complexity.
Before you start
- Confirm the property line, height limits and any HOA rules before you order.
- Mark gate positions first — each gate needs its own strong posts.
- Call 811 (or your local utility locator) before digging post holes.
Questions about this project
How deep should fence posts be?
A common rule is one third of the post height above ground, at least 24 in, and below the frost line where it freezes.
Panels or pickets?
Prebuilt panels are faster and fix the post spacing; pickets on rails follow slopes and curves better and let you choose the gap.
Calculators used in this project
Need just one number? Each step is also a stand-alone calculator.