How to measure
- Measure the surface length and width (or wall width and height) in feet or inches. For walls, stop at the height the tile will reach.
- Measure an actual tile — nominal sizes like '12 × 24' can be a few millimetres off.
- Decide the grout joint before buying: ⅛ in (3 mm) is typical, 1/16 in for rectified tile, ¼ in for rustic or handmade tile.
- Subtract areas that won't be tiled (a vanity footprint, a tub) by tiling around them as separate rectangles.
How the tile calculation works
Area = length × width Tile + joint = (tile width + joint) × (tile length + joint) Tiles = area ÷ (tile + joint), rounded up Tiles to buy = tiles × (1 + waste %), rounded up Boxes = tiles to buy ÷ tiles per box, rounded up
Each tile occupies its own area plus one grout joint on two sides. Including the joint matters most for small tiles: on 4 × 4 in tile with ⅛ in joints, joints are about 6% of the surface.
Waste covers the cut tiles along edges and around obstacles, plus breakage. The calculator also shows the straight-grid count, where every partial edge tile is counted as a whole one — a useful upper bound in small rooms.
Grout is estimated from the volume of the joints (joint width × tile thickness × joint length) at the density of dry grout powder.
Worked example
An 8 × 5 ft bathroom floor in 12 × 12 in tile with ⅛ in joints, laid straight, 10 tiles per box.
- Area: 8 × 5 = 40 sq ft
- Tile + joint: 12.125 × 12.125 = 147.0 sq in = 1.021 sq ft
- Tiles: 40 ÷ 1.021 = 39.2 → 40 tiles
- With 10% waste: 39.2 × 1.1 = 43.1 → 44 tiles
- Boxes: 44 ÷ 10 = 4.4 → 5 boxes
Buy 5 boxes (50 tiles). The 6 spare tiles cover breakage and a few future repairs.
How much extra to allow
Tile waste is mostly edge cuts. The larger the tile relative to the room, the more of each edge tile ends up in the bin.
| Situation | Allow |
|---|---|
| Straight lay, small or medium tile | 10% |
| Diagonal lay | 15% |
| Herringbone, or large-format tile in a small room | 15–20% |
| Natural stone with color variation | +5% for selection |
Reading your result
Buy by the highlighted box count — stores rarely split boxes.
Check that every box carries the same lot (shade) number. Mixing lots shows up as color banding.
If you're tiling floor and walls with different tiles, run the calculator once for each, or use the Bathroom Tile Calculator.
Assumptions
- A rectangular surface. For L-shapes, calculate each rectangle separately and add the tile counts.
- Grout estimate assumes the joint is filled to the full tile thickness. Manufacturers' charts vary; buy the next bag size up if close.
- Tiles per box is taken from the label. Loose tile sold individually: set it to 1.
Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.
When to call a professional
- Shower pans, waterproofing and large-format tile on walls are common failure points — a professional or the manufacturer's install guide is worth following closely.
- Tile over a wood subfloor needs enough stiffness to avoid cracked tiles and grout; check the deflection rating.
Frequently asked questions
How many 12 × 12 tiles do I need for 100 sq ft?
About 98 tiles with ⅛ in joints, so 108 with 10% waste — 11 boxes of 10.
How many 12 × 24 tiles are in a square foot?
One 12 × 24 tile covers 2 sq ft, so about 0.49 tiles per sq ft including ⅛ in joints.
Does grout spacing change how many tiles I need?
Slightly. Wider joints mean fewer tiles: with 4 in tiles, going from 1/16 to ¼ in joints reduces the count by about 8%.
How much grout do I need?
It depends on tile size, joint width and tile thickness. Small mosaics with wide joints can use ten times more grout per square foot than large tiles with thin joints. The calculator estimates it from your inputs.