How to measure
- Slabs: measure length and width at the inside of the forms, and the thickness you'll pour (not the form board height if the subgrade is uneven).
- Round pads and columns: measure the diameter — across the middle — and the thickness or height.
- Walls: length, height and thickness of the poured section. Measure footings separately with the Footing Calculator.
- Steps: count the steps and measure one step's rise and tread depth, plus the width of the flight.
- Several identical pieces, like deck pier holes? Enter one and set 'How many'.
How the concrete calculation works
Slab = length × width × thickness Round = π × (diameter ÷ 2)² × thickness Column = π × (diameter ÷ 2)² × height Wall = length × height × thickness Steps = Σ width × run × (rise × step number) Cubic yards = cubic feet ÷ 27 Bags = volume × (1 + waste) ÷ bag yield
Every shape reduces to an area times a depth. The calculator converts all measurements — feet, inches, metres — to one unit first, so mixing inches of thickness with feet of length can't go wrong.
Cubic feet divide by 27 to give cubic yards because a yard is 3 ft in each direction. Bag counts use the manufacturers' published yields: 0.60 cu ft for an 80 lb bag, 0.45 for 60 lb, 0.30 for 40 lb.
Ready-mix plants sell in quarter-yard increments, so the order quantity rounds up to the next ¼ yard after waste is added.
Worked example
A 10 × 10 ft patio slab, 4 in thick, with 10% extra.
- Thickness in feet: 4 ÷ 12 = 0.333 ft
- Volume: 10 × 10 × 0.333 = 33.3 cu ft
- In cubic yards: 33.3 ÷ 27 = 1.23 cu yd
- With 10% waste: 1.23 × 1.1 = 1.36 cu yd (36.7 cu ft)
- 80 lb bags: 36.7 ÷ 0.6 = 61.1 → 62 bags
Order 1.5 cubic yards of ready-mix, or buy 62 × 80 lb bags. At this size the truck is usually cheaper and spares you lifting 2½ tons of bags.
How much extra to allow
Concrete is the one material where running short is a real problem: a delay between loads leaves a weak 'cold joint'. Order a little over.
| Situation | Allow |
|---|---|
| Formed slab on a compacted, level base | 5% |
| Typical patio, walkway or footing | 10% |
| Uneven ground, post holes dug by hand | 10–15% |
Reading your result
The highlighted row is how to buy: bags for small pours, ready-mix above roughly 1½ cubic yards.
Ready-mix orders under about 4–6 yards usually carry a short-load fee. Use the Concrete Cost Calculator to compare the real totals.
The weight figure is a reminder of what you'll lift: an 80 lb bag every 0.6 cu ft adds up fast.
Assumptions
- Bag yields are for standard premixed concrete (about 0.0075 cu ft per lb). High-strength and fast-setting mixes yield slightly less — check the bag.
- Concrete weighs about 150 lb per cubic foot (2,400 kg/m³) when cured.
- Forms are square and the subgrade is level. If the ground dips, the slab is thicker there and uses more concrete.
Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.
When to call a professional
- Driveways, structural slabs, foundations and retaining walls need the right strength, reinforcement and base — get local guidance or a contractor.
- Pours over about 3 yards go much better with a crew and a pump or chute access for the truck.
Frequently asked questions
How many bags of concrete do I need for a 10 × 10 slab?
At 4 in thick, a 10 × 10 slab is 1.23 cubic yards. With 10% extra that's 62 bags of 80 lb premix or 82 bags of 60 lb.
How do I convert cubic feet to cubic yards?
Divide by 27. For example, 54 cubic feet is 2 cubic yards.
When should I order ready-mix instead of bags?
Above about 1 to 1.5 cubic yards. Bags are practical for posts, small pads and repairs; beyond that, ready-mix is usually cheaper, more consistent and far less work.
How thick should a concrete slab be?
4 in for patios, walkways and shed floors; 5–6 in for driveways or anywhere vehicles park. Thickened edges help under walls and at slab edges that see loads.
Is cement the same as concrete?
No. Cement is the powder that binds concrete; concrete is cement mixed with sand, gravel and water. If you're mixing your own from bulk materials, use the Cement Calculator.