Skip to content
MeasureToBuy

Roofing Calculator

Enter the building footprint, overhang and roof pitch. The calculator works out the sloped roof area, converts it to squares and shingle bundles, and lists underlayment, starter, ridge cap, drip edge and nails.

Footprint-and-pitch estimates suit simple gable and hip roofs. Roofs with dormers, multiple pitches or many valleys should be measured by a roofer.

Measurements

Along the ridge / eaves.

Eave to eave across the slopes.

Added to every edge. 0 if you measured at the drip edge.

Rise in inches per foot of run. Count it with a level and tape, or from the plans.

Roof style

Two slopes, triangular ends

Waste allowance

Cut-offs at hips, valleys and rakes. Hip roofs need more than gables.

Advanced optionscoverage, sizes, custom values
Bundles per square

Most architectural and 3-tab shingles

Underlayment

10 squares per roll

Your estimate

You need 50 bundles of shingles.

1,503 sq ft of roof = 15.0 squares, plus 10% waste, at 3 bundles per square.

Footprint incl. overhang42 ft × 32 ft
1,344 sq ft
Pitch
6/12 · 26.6°
Pitch multiplier
1.12
Roof surface area
1,503 sq ft
Roofing squares
15 squares
Waste allowance
10%
Squares with waste
16.5 squares
Shingle bundles3 per square
50 bundles

Accessories

Ridge cap42 ft of ridge
2 bundles
Starter strip156 ft of eaves and rakes
2 bundles
Underlayment10 squares per roll
2 rolls
Drip edge10 ft pieces
17 pieces
Roofing nails1 coil box of 7,200
5,290 nails
  • Tear-off disposal, flashing, vents and ice-and-water shield in valleys are not included.
Roof · end elevation and plan
run ½ 30 ftrise 6/12RAFTER40 ft30 ftPLAN · GABLE
A 6/12 roof rises 6 in for every 12 in of run (26.6°). Sloped area = footprint × 1.118.

Next step

Estimate the cost

You need 50 bundles plus accessories. Enter local prices to total the materials.

Estimate roofing cost

Also useful

Plan the whole re-roof

Step through measurements, pitch, waste and every material, then print an order list.

Start the Replace a Roof project

How to measure

  1. Measure the building's length and width at the walls. Then measure how far the eaves overhang the walls — usually 12 to 24 in.
  2. Find the pitch: hold a level horizontally against a rafter or the roof surface, mark 12 in along it, and measure straight up to the roof. That number over 12 is the pitch.
  3. Note the roof style. Gable roofs have triangular end walls; hip roofs slope down on all four sides.
  4. Measuring from the ground is fine for simple roofs. For several roof sections, run the calculator for each and add the results.

How the roofing calculation works

Footprint      = (length + 2 × overhang) × (width + 2 × overhang)
Pitch factor   = √(1 + (rise ÷ 12)²)
Roof area      = footprint × pitch factor
Squares        = roof area ÷ 100 sq ft
Bundles        = squares × (1 + waste %) × bundles per square, rounded up

A sloped roof is longer than the ground it covers. The pitch factor is the slope length per foot of horizontal run — 1.118 for a 6/12 roof — and multiplying the footprint by it gives the true surface area. For a roof with one pitch, this holds for gable and hip shapes alike.

Roofing is counted in squares of 100 sq ft. Most architectural shingles come three bundles to a square; check the wrapper.

Ridge cap is estimated from the ridge and hip length at about 33 ft per bundle, starter strip from the eaves and rakes at about 105 ft per bundle, and drip edge in 10 ft pieces along the same edges.

Worked example

A 40 × 30 ft gable roof at 6/12 pitch, measured at the drip edge, with 10% waste.

  1. Footprint: 40 × 30 = 1,200 sq ft
  2. Pitch factor for 6/12: √(1 + 0.5²) = 1.118
  3. Roof area: 1,200 × 1.118 = 1,342 sq ft = 13.4 squares
  4. With 10% waste: 13.4 × 1.1 = 14.8 squares
  5. Bundles: 14.8 × 3 = 44.3 → 45 bundles

Order 45 bundles of shingles, 2 bundles of ridge cap, 2 of starter strip, 2 rolls of synthetic underlayment and 16 pieces of drip edge.

How much extra to allow

Roof waste comes from cuts at rakes, hips and valleys. Every hip and valley adds two cut lines along its whole length.

SituationAllow
Shed roof5%
Simple gable10%
Hip roof15%
Multiple valleys, dormers20%

Reading your result

The headline is the shingle bundle count. Accessories are listed separately because they're bought separately — and running out of ridge cap stops the job just as surely as running out of shingles.

Suppliers often deliver to the roof. Give them the bundle and accessory list from this estimate.

Assumptions

  • Every roof plane has the same pitch. Mixed pitches, dormers, turrets and porches need separate measurements.
  • Waste of 10% suits a plain gable; hip roofs and roofs with valleys need 15% or more.
  • Nail count assumes about 320 nails per square (four per shingle) and 7,200-count coils.
  • Flashing, vents, ice-and-water shield, valley metal and tear-off disposal are not included.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

When to call a professional

  • Roofs steeper than about 8/12, two-storey eaves, or any roof with soft decking need professional crews and fall protection.
  • Complex roofs should be measured by a roofer or from aerial measurement reports.

Frequently asked questions

How many bundles of shingles do I need for 1,000 sq ft?

1,000 sq ft is 10 squares. At three bundles per square and 10% waste, that's 33 bundles.

How do I calculate roof area from the ground?

Measure the footprint including overhangs and multiply by the pitch factor: 1.054 for 4/12, 1.118 for 6/12, 1.202 for 8/12, 1.414 for 12/12.

What is a roofing square?

A square is 100 sq ft of roof surface. Shingle prices and labour quotes are often given per square.

Do hip roofs need more shingles than gable roofs?

For the same footprint and pitch the area is the same, but hip roofs need more waste (about 15%) and much more ridge cap because every hip is capped.

More roofing, siding & gutters calculators

All roofing, siding & gutters